ماژول Timer Module Relay 5 Functions:

ماژول Timer Module Relay 5 Functions دارای رله یک ماژول بسیار کاربردی است که قابلیت های جذابی برای آن طراحی شده است. این ماژول قابل برنامه ریزی، قابلیت تحریک شدن توسط سیگنال بیرونی را داشته و می تواند با چند حالت، خروجی آن فعال شود: از جمله Delay on Start, Delay on Stop or Recycling و …

مشخصات محصول:

ابعاد: 62x38x17mm
وزن: ~100gr
ولتاژ کاری: 6-30VDC
نوع خروجی: رله ۱۰ آمپر
جریان خروجی: Up to 10A
زمان تاخیر: ۰.۱ ثانیه تا ۹۹۹ دقیقه
Trigger: ۳-۲۴ ولت

 

One relay module, delay power off, disconnect, trigger delay, cycle timing circuit switch

0.1 second (minimum) ~ 999 minutes (maximum) continuously adjustable

This product is easy to use and powerful, but buyers please read the operation instructions of this product in detail. It is a very practical product.

Module highlights:

1. Wide voltage power supply (6~30V) supports micro USB 5.0V power supply, which is very convenient to use;
2. The interface is clear and simple, powerful, easy to understand, and almost meets all your needs;
3. There is a key emergency stop function (STOP key), with reverse connection protection, reverse connection does not burn;
4. Added sleep mode, after enabling it, without any operation within 5 minutes, automatically turn off the display; any key to wake up;
5. Different OP, CL, LOP parameters can be set, these parameters are independent of each other and saved separately;
6. All setting parameters are automatically saved after power-off.

Operating mode:

P1: After the signal is triggered, the relay is turned on for OP time and then turned off; during OP time, the following operations.
P1.1: Signal is invalid when triggered again
P1.2: The signal is triggered again to re-timing
P1.3: The signal triggers the reset again, the relay is disconnected, and the timing stops;
P-2: Give the trigger signal, after the relay is turned off for CL time, the relay is turned on for OP time, after the timing is completed, the relay is turned off;
P3.1: Give the trigger signal, after the relay is turned on for the OP time, the relay will disconnect for CL time, and then cycle the above actions, give the signal again in the cycle, the relay will disconnect, and stop timing; the number of cycles (LOP) can be set;
P3.2: There is no need to trigger signal after power-on, the OP time when the relay is on, and the CL time when the relay is off, the above actions are cycled; the number of cycles (LOP) can be set;
P-4: Signal hold function. If there is a trigger signal, the timer is cleared and the relay remains on; when the signal disappears, the relay is disconnected after timing the OP; during the timing, there is another signal, and the timer is cleared;

Product parameters:

1: Working voltage: 6-30V support micro USB 5.0V power supply
2: Trigger signal source: high-level trigger (3.0V-24V) The signal ground and the system ground are not in the same ground to improve the anti-interference ability of the system (also can be short-circuited to the common ground)
3: Output capacity: can control equipment within DC 30v 5A or AC 220v5A
4: Quiescent current: 20mA Working current: 50mA
5: Service life: more than 100,000 times; working temperature: -40—85°C; size: 6.2*3.8*1.7cm
6: With optocoupler isolation, enhanced anti-interference ability, industrial grade circuit board, set parameters forever after power off

memory.

Special attention: The relay output is a passive contact, uncharged output, which controls the on-off function of a line.

6-30V Relay Module Switch Trigger Time Delay Circuit Timer Cycle Adjustable